Bunn Hot Water Dispenser User Manual Scalding

HW2

1. Bunn Hot Water Dispenser User Manual Scalding Instructions
2. Bunn Hot Water Dispenser Parts

HW2A

BUNN OHW Pourover Hot Water DispenserThis BUNN OHW hot water dispenser holds up to 80 Oz. Of water and dispenses it at a temperature of 200 degrees. SERVICE & REPAIR MANUAL BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS. This equipment will brew a half-gallon batch of coffee into an awaiting dispenser. It can be easily configured for. 120V 15 amp, 120/208V 20 amp or 120/240V 20 amp. The brewer may have a hot water faucet for allied beverage use. Empty water bottle (if applicable) and then remove it from the dispenser. Drain cold water reservoir by dispensing water through the cold water faucet. Drain hot tank by unscrewing drain cap and removing red silicone plug at the rear of the dispenser. Drain water into a bucket or container (approx. Shop Juice at BUNN.com. BUNNserve Support Locations. Orders: (800) 626-2866. Hot Chocolate/Cappuccino Hot Water Liquid Coffee Water Filters Accessories Grinders Serving & Holding Paper Filters Supplies. Product Family Category. Spec sheet Parts manual.

HOT WATER DISPENSERS

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION

This equipment heats and dispenses water on demand for beverages and cooking purposes.

WARRANTY

Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date of installation. In addition:

1.) Bunn warrants electronic circuit and/or control boards to be commercially free from defects in material and workmanship for two years from the date of installation.

Bunn Hot Water Dispenser User Manual Scalding Instructions

2.) Bunn warrants the compressor on refrigeration equipment to be commercially free from defects in material and workmanship for two years from the date of installation.

3.) Bunn warrants that the grinding burrs on coffee grinding equipment will grind coffee to meet original factory screen sieve analysis for three years from date of installation or for 30,000 pounds of coffee, whichever comes first.

This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that, in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are not authorized to make modifications to this warranty or to make additional warranties that are binding on Bunn. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.

The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge for parts during the warranty period and no charge for labor by a Bunn Authorized Service Representative during the warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND.

In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

USER NOTICES

The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels.

00657.0000

00831.0000

Bunn Hot Water Dispenser Parts

ELECTRICAL REQUIREMENTS

CAUTION - The dispenser must be unplugged until specified in Initial Set-Up.

The Model HW2 has an attached cordset and requires 2-wire, grounded service rated 120V ac, 15 amp, single phase, 60 Hz. The Model Hw2A requires 2-wire grounded service rated 240V ac, 8 amp, single phase, 50 Hz.

PLUMBING REQUIREMENTS

This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1/2' or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1/4' flare.

NOTE - Bunn-O-Matic recommends 1/4' copper tubing for installations of less than 25 feet and 3/8' for more than 25 feet from the 1/2' water supply line. A tight coil of copper tubing in the water line will facilitate moving the dispenser to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Oficials and Code Administrators Internatiopnal, Inc. (BOCA)

and the Food Service and Drug Administration (FDA).

Plumbing Hook-Up

1.Flush the water line and securely attach it to the bulkhead fitting on the rear of the machine.

2.Turn-on the water supply.

INITIAL SET-UP

CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions.

1.Remove the center rear panel and rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the panel.

2.Plug-in the dispenser.

3.Water will automatically flow into the tank to the proper level and shut-off.

4.Unplug the dispenser, remove the center rear panel and rotate the control thermostat knob fully clockwise to the “ON” position, and replace the panel.

5.Plug-in the dispenser and wait approximately twenty minutes for the water in the tank to heat. The dispenser is ready for use.

CLEANING

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment.

WIRING DIAGRAMS

SCHEMATIC WIRING DIAGRAM HW2
L1	SW. &	LIMIT	GREEN		N
THERMOSTAT
THERMOSTAT			1700W
BLK	BLK	BLK		WHI
			TANK HEATER
WHI	40W	WHI
	WHI		KEEP WARM HEATER			40W	WHI
KEEP WARM HEATER
LIQUID
LEVEL
BOARD
SAFETY SW	1	2 3 4
	BLU/BLK	SOL	WHI
BLK				RED	RED	BLK
	WHI
P
120 VOLTS A C		N
		K
2 WIRE	(PROBE)
SINGLE PHASE
10261.0000E 5/98 © 1987 BUNN-O-MATIC CORPORATION

SCHEMATIC WIRING DIAGRAM HW2A
GRN/YEL
L1	SW. &	LIMIT	BLK	L2
THERMOSTAT
BLK	THERMOSTAT			1700W	RED
	BLK
TANK HEATER
WHI	34W	RED
WHI	KEEP WARM HEATER			34W	RED
	KEEP WARM HEATER
LIQUID
LEVEL
BOARD
SAFETY SW	1	2 3 4	BLU/BLK	RED
	BLK	RED			BLK	SOL
RED			RED
P
240 VOLTS A C		N
		K
2 WIRE	(PROBE)
SINGLE PHASE
10261.0001E 5/98 © 1998 BUNN-O-MATIC CORPORATION

To continue the download you need to go through the captcha: